Used machines for pallet shops, by make and model.

Find me a machine
Menu
Recovered pine deck boards riding a chain feed into a trim saw under a steel guard

Pallet trim saws

A trim saw squares the ends of recovered boards and cuts them to the lengths you rebuild with, usually right after the dismantler. They come as single-end power-feed saws, double-end saws that trim both ends at once, and multi-head saws with two to seven blades for cut stock, and the makers’ figures run from a few thousand boards a shift to tens of thousands.

Trim saws by maker #model with the guide’s figures
Maker and modelKindPowerSize and capacityMaker’s output claim
Wood-Mizer PC200Single-end power feed18 in blade21 to 66 in long, up to 2 in thickup to 12,000 boards a shift[1]
Smart Products single-end power feedSingle-end10 HP three-phase; single-phase optional18 to 60 in, up to 2 in thick15,000 boards an 8-hour shift[1]
Industrial Resources Quick CutTrim saw, nail-buster blade10 HP; single-phase option16 in bladeup to 4,200 cuts an hour[1]
PRS DUALMAXDouble-endTwo 7-1/2 HP motorsTrims up to 66 in to 30–60 in partsup to 4,000 pieces an hour[1]
Universal hopper-feed double end-trimDouble-end10 in blades (12 in optional)20 to 60 in47 to 50 boards a minute[1]
PRS AUTOMAXScan, trim and sort, 5 sawsup to 30,000 pieces a shift[1]
Go Fast MET-20Multi-head, 2 to 7 heads10 HP a head, 20 in bladesup to 20 ft long, 5-1/2 in thickup to 45 cuts a minute[1]
Pendu multi-saw trimmerMulti-head, 3 to 7 saws10, 15 or 20 HP, 22 in bladesup to 20 ft or longer28 to 40 lugs a minute feed[1]

A dash means the maker’s page or the listing gave no figure for that column.

Output figures are the makers’ own claims as the source prints them, not our measurements.

  1. Pallet Enterprise trim saw guide, April 2024, read Nov 15, 2026

Published asks

Trim saws: asking prices as listed
Maker and modelMachineYear and conditionListed fromAsk
Brewco pallet sawPallet saw, 167 in conveyor, 30 HP, three-phaseYear and condition not listedEuclid, OH, Surplus Record$2,719

Asks, not sales: what each seller listed when we read the page on 15 Nov 2026. We are not the seller of these machines, and a listed machine may since have sold.

Which trim saw for which shop

A recycler rebuilding stringer pallets from recovered boards usually starts with a single-end power-feed saw beside the dismantler: one blade, a chain feed, boards in one at a time. The Wood-Mizer PC200 and Smart Products’ machine are the examples in the guide, with nail-cutting blades because recovered boards carry nail shanks.

Double-end saws trim both ends in one pass and size the board to a set length, which matters when you build to a customer’s print. Multi-head saws are for cutting new lumber into stringers and deck stock; they belong in a new-pallet shop more than a recycler’s. Small shops often get by with a chop saw first.

What to check used

Look at the arbor bearings, the chain or lug feed and its sprockets, and the blade guard. Ask whether the blade is a nail-cutting blade and when it was last sharpened. Check the motor nameplate: Smart Products’ saw is 10 HP three-phase as standard, with single-phase optional, and that choice decides whether it runs in your building.

Measure the length range against your boards. A saw that trims 21 to 66 inches will not handle 72 inch deck boards. Send us the lengths you rebuild with and we will look for a saw that covers them.

Where the saw goes in the line

A trim saw lives right behind the dismantler: boards come off with ragged, split or nail-damaged ends, and the saw squares them to standard lengths for the repair tables or the nailer. Where floor space is short, a conveyor carries boards from one to the other. When you buy a used saw, measure the distance between the dismantler’s out-feed and the saw’s in-feed in your building before you agree on a model.