How to start a pallet recycling business
To start a pallet recycling business you need a steady supply of used pallets, somewhere to work them, and a short list of machines bought in order: a bandsaw dismantler and a trim or chop saw first, then repair tables, then a notcher, a nailer and a grinder as the volume comes.

Start with the cores, not the machines
A recycler lives on cores: the used pallets that come back from warehouses, factories and stores. Before you buy anything, know where your cores will come from, how many a day, and what condition they arrive in. A stream of good 48 x 40s that only need a board or two is a repair business; a stream of broken, odd-size pallets is a dismantling and lumber business. The machines follow from that.
The trade press has said for years that cheap or free cores are what make the numbers work. Our guide to what decides a recycler’s margins goes into it.
First: a dismantler and a saw

The bandsaw dismantler is the first machine most recyclers buy. It cuts the nails between boards and stringers so you recover lumber from pallets that cannot be repaired. Makers rate them from about 400 pallets a shift, the figure given for Wood-Mizer’s Pallet Hawg PD200, up to 800 to 1,000 for Industrial Resources’ Rapid Cut II, depending on model and crew.
Recovered boards need squaring and cutting to length, so a saw comes with it. A chop saw is the cheap start: one cut at a time. A power-feed trim saw such as the Wood-Mizer PC200, rated by the maker at up to 12,000 boards a shift, is the step up when the chop saw is the bottleneck.
Power decides a lot here. Most stationary machines want three-phase. If your building only has single-phase, look at gas machines such as the Pallet Hawg gas version or the Cam-Wood 1AM-010-2G, or electric models offered single-phase, such as Universal’s Mark I and the Wolverine II option.
Then: repair tables

Many cores need only a broken board replaced. A repair table with a nail gun on a balancer, a compressor and a bin of recovered boards turns those into saleable pallets quickly, using the lumber the dismantler produced. Most shops add tables as soon as the dismantler is running.
Later: notcher, nailer, grinder

A notcher comes when customers want 4-way stringers. A nailing machine comes when hand nailing at the tables cannot keep up with orders for rebuilt or combo pallets. A grinder or shredder comes when the scrap pile costs more to haul away than it would cost to grind, and there is a buyer for mulch, bedding or fuel.
Each of these can be bought used. Published asks we found in November 2026 run from $5,985 for a new single head notcher to $50,000 for a used 2023 Pallet Chief IV with stacker; most used listings say Request Price.
What the trade press said it costs

A 2000 Pallet Enterprise article said a recycler could begin with as little as $30,000 of new recycling machinery. That figure is more than 25 years old. We do not put a total on starting a shop: it depends on the machines, their age and condition, your building and your power. The cost guide lays out the published asks we hold instead.
The same article said that in most states, equipment used for pallet manufacturing or recycling is exempt from sales tax. Rules vary and change; check with your state before you buy.
Plan it before you buy
Our Start-up Line Planner takes the work you will do, your pallets a day and your power, and lists the machines in buying order with the makers’ output figures beside your count and the asks we hold. It does not total a cost. When the list looks right, send it to us and we will look for the machines.
The building
Pallets take room. Cores arrive by the trailer load and wait in stacks; recovered boards need sorting space by length; finished pallets wait for pickup. Look for a yard you can stack in, a floor that takes a forklift, doors a trailer can back up to, and enough height to stack inside in bad weather. Ask the landlord about the power before you sign, because it decides which machines you can run.
People and safety
A small recycling shop runs on a few people: someone on the dismantler, someone squaring boards, people at the repair tables, and a forklift driver who also loads trucks. Machines decide how many pallets each of them handles, so count heads before you count machines. A dismantler that needs two people to feed it at full rate is a different buy for a three-person shop than for a ten-person one.
Bandsaws, chop saws and nail guns are dangerous in tired hands. Guards, hearing and eye protection, push sticks and lockout on every machine are part of the setup. A used machine missing its guards needs them replaced before anyone runs it, and that is worth checking before you agree a price.
| Machine | For example | Maker’s figure |
|---|---|---|
| Bandsaw dismantlers | Industrial Resources Rapid Cut II, 15 HP direct drive, 4,200 ft/min | 800 to 1,000 a shift |
| Chop saws | Universal Robo-Chop, Not stated | about 2 seconds a cycle |
| Trim saws | Wood-Mizer PC200, 18 in blade | up to 12,000 boards a shift |
| Repair tables | PRS Econo, 3/8 in steel plate top | Hold-down bracket with 4.5 in lip |
| Pallet notchers | Cam-Wood 1AM-1150, 10 HP | Not stated |
| Pallet nailing machines | Viking Turbo 606, Three operators | upwards of 2,000 a shift |
| Pallet grinders | Cresswood XR500 Series, Not stated | 3,000 to 5,000 lb an hour |
Sources for this guide
Ask for your first machines
Tell us the work, your pallets a day and the power at your building, and we will look for the dismantler and saw that fit. If you have used the Line Planner, send its list.
Bandsaw dismantler