What to check on a used pallet dismantler
On a used bandsaw pallet dismantler, check the blade guides, the wheel bearings and tires, and how the table raises before anything else, then the tensioner, the motor and the power it needs; paint tells you very little.

Blade guides

The guides hold the blade flat and straight in the cut. When their bearings or blocks wear, the blade wanders, rides up into the boards, heats up and breaks early. Look at the guide bearings for flats and play, spin them by hand, and check that the guides sit square to the table. Smart Products names blade guide bearings as a feature of its machines because this is where dismantlers wear.
Wheels, tires and bearings
With the blade off, spin each wheel and listen. A rough or noisy bearing will fail. Look at the tires or the wheel surfaces for wear, cracks and grooves; some machines run large pneumatic drive and idler tires, like Industrial Resources’ Rapid Cut II and Wolverine II, and those need the right pressure. Check the wheel alignment: the blade should track in the middle of both wheels.
Table and lift
The table sets the height of the cut against the stringer. Run it through its full travel, with a pallet on it. On a pneumatic lift like the Pallet Hawg’s, listen for leaks; on a hydraulic one, look for weeping cylinders and slow travel; on a push-button powered lift, check the motor and the limit switches. Look at the table plate for dents and gouges where the blade has hit it.
Tension, blade and blade life
Tensioning varies by maker: mechanical on the Spartan and the Pallet Hawg, pneumatic or air spring on the Industrial Resources machines, hydraulic on Smart Products’. Check that it holds. Ask what blade the seller runs and how many pallets they get from one. Makers state 1,200 to 1,500 pallets a blade for Smart Products’ machine and up to 1,500 for the Pallet Hawg; a shop getting far fewer has guide, tension or wheel trouble. Blades are on the blades page.
Motor, engine and power
Read the motor nameplate: horsepower, voltage and phase. Most bandsaws are 10 or 15 HP, and a 15 HP motor normally means three-phase. If your shop is single-phase, buy a single-phase or gas model rather than plan on converting. On a gas machine, start it cold and ask for engine hours. Check the starter, the stop buttons (the Pallet Hawg has remote stops for two operators) and the guards.
Ask the seller
Why it is for sale. How many pallets a day it did. What was replaced and when. Whether it has been moved before, and how it will come out of the building. Used machines are usually sold as-is, so what you see is what you get; get photos of the guides, wheels, nameplate and table, or go and see it run. The machines themselves are on the bandsaw dismantler page.
Run it before you pay
Ask the seller to run pallets through it while you watch, ideally the kind you will run. Listen for bearing noise, watch the blade track on the wheels, see whether the table holds its height under load, and look at the boards that come off: clean cuts close to the stringer mean sharp blades and good guides; torn or wavy cuts mean something is worn. Time ten pallets.
If you cannot see it run, ask for a video taken with the guards in place, the nameplate in view and the hour meter shown, and buy knowing that it is sold as-is.
Paperwork and parts
Ask for the manual, the wiring diagram and the parts list. A machine without them can still be a good buy, but you will spend time finding blade lengths, bearing numbers and belt sizes that the paperwork would have given you. Ask what spare blades, guide bearings and tires come with it.
Ask why it is being sold. A shop that bought a faster machine or closed a line is a different seller from one getting rid of a dismantler that never ran well. Both are common; the answer tells you which questions to press.
Leverage and rotary machines
Leverage dismantlers need tight cylinders, sound hold-downs and a compressor that keeps up; rotary machines need sharp heads and a healthy hydraulic pusher ram. Bring a flashlight, a tape measure and gloves. Note rust.
| Machine | For example | Maker’s figure |
|---|---|---|
| Dismantler blades | PRS Spartan, 2,200 SFPM | Not stated |
| Bandsaw dismantlers | Industrial Resources Rapid Cut II, 15 HP direct drive, 4,200 ft/min | 800 to 1,000 a shift |
Sources for this guide
Ask us for a dismantler that passes
Tell us the dismantler you want, bandsaw or leverage, your power and your pallets a day. When we find one, these are the questions we put to the seller.
Bandsaw dismantler