Used machines for pallet shops, by make and model.

Find me a machine
Menu
A whole bandsaw dismantler mid-cut, a used pallet crossing its table and freed boards sliding off the far end

Pallet dismantlers

A pallet dismantler takes a used pallet apart so its deck boards and stringers can be trimmed and nailed into another pallet. There are four kinds: bandsaw machines that cut the nails, rotary or disc machines that shear them, leverage machines that pry boards off on air, and robotic lines that do it with conveyors and a robot.

Dismantlers by maker and model, as the trade guide lists them
Maker and modelKindPowerSize and capacityMaker’s output claim
Industrial Resources Rapid Cut IIBandsaw, one operator15 HP direct drive, 4,200 ft/min64 in table800 to 1,000 pallets a shift[1]
Smart Products one-operatorBandsaw10 or 15 HP electric52 or 64 in base600 pallets an 8-hour shift[1]
Wood-Mizer PD200 Pallet HawgBandsaw, one or two operators10 HP electric or 19 HP gas, 2,200 ft/min60 to 96 in tablesabout 400 pallets a shift[1]
Universal Machinery Sales TrioDisc (shear), 3 heads15 HPPallets up to 54 x 62 in800 to 1,000 pallets a shift[1]
PRS Recycler 3-HeadRotary15 HP hydraulics on the pusher ramTool steel blades, built-in lumber conveyors[1]
Bronco leverage dismantlerLeverage, air100 PSI compressed airAdjusts to pallet size60 to 80 an hour, 400 to 600 a day[1]
Alliance Automation Robotic Pallet DismantlerRobotic lineStringer, skid and block pallets[1]

A dash means the maker’s page or the listing gave no figure for that column.

Output figures are the makers’ own claims as the source prints them, not our measurements.

  1. Pallet Enterprise dismantler guide, July 2025, read Nov 15, 2026

Published asks

Pallet dismantlers: asking prices as listed
Maker and modelMachineYear and conditionListed fromAsk
Cam-Wood 1AM-010-2GGasoline bandsaw pallet dismantler, 13 HP, 60 x 48 in table, 251 in blade2026, newCharlotte, NC, Surplus Record$8,925
Wood-Mizer pallet dismantlerBandsaw pallet dismantler, listed as barely usedusedUxbridge, ON, Surplus Record$10,878

Asks, not sales: what each seller listed when we read the page on 15 Nov 2026. We are not the seller of these machines, and a listed machine may since have sold.

Which kind a shop buys

Most recyclers buy a bandsaw dismantler first. The blade runs flat across the table and cuts the nail shanks between board and stringer, so the boards come off clean and quick, a little thinner where the blade ran. It is the machine we are asked for most.

A leverage dismantler pries each board off whole, nails still in. The board keeps its full thickness, there is no blade to buy, and it runs on shop air. It is slower per pallet than the faster bandsaws, and somebody has to punch or pull the nails afterwards.

Rotary and disc machines shear the nails with heads instead of a band. Universal’s Trio and PRS’s Recycler are the names you see. Robotic lines sit at the other end: a robot, a bandsaw, conveyors and a vacuum system, sold as a project.

What to check on a used one

On a bandsaw machine, look at the blade guides, the wheel bearings and how the table raises before you look at the paint. Ask what blade it runs and how long one lasts in that shop. Ask whether the motor is single-phase or three-phase, and what the seller had it wired to.

On a leverage machine, check the air cylinders and the hold-down for leaks and play, and ask what compressor it ran on. On a rotary machine, look at the heads and the hydraulic pusher. Our used dismantler checklist goes through it part by part, and the blade page covers what wears.

Selling a dismantler

Dismantlers are the machines buyers ask us for most, so a running one rarely waits long for interest. Send the maker and model, the motor and phase, the table width and the blade length, and say whether it was a one-person or two-person setup in your shop. A photo of the blade guides and the wheels tells a buyer more than a photo of the whole frame.