Certifying a used pallet kiln
A used pallet kiln has to be certified again where it is installed: you enrol with an inspection agency accredited by the American Lumber Standard Committee, and the agency checks that the kiln brings the wood core to 56 °C for at least 30 minutes before you can stamp pallets with the ISPM 15 mark.

The rule
USDA APHIS says heat-treated wood packaging must reach a core temperature of 56 °C for at least 30 minutes, and that producers must enrol with an ALSC-accredited inspection agency. The international standard behind it is ISPM 15, and the mark it allows is the HT stamp on export pallets.
The certification is of your operation, not of the box. It covers how you load, where the probes go, how you record each charge and how you mark the pallets. Move the kiln and the operation is new.
Before you buy

Ask the seller which agency certified the kiln before, and for the records the agency approved: probe placement, charge records, the control system and its software. They tell your new agency how the kiln has been run. Ask whether the temperature probes, data loggers and recording software come with the kiln; Kiln-Direct, for example, lists wireless record keeping and touchscreen controls, and that kit may be licensed to the seller.
Check the chamber for corrosion and damaged insulation, the doors and seals, the burner or heat exchanger, the fans and the controls. A kiln that cannot hold temperature evenly will struggle to pass.
Fuel and capacity
Capacity is quoted in GMA pallets, the 48 x 40 stringer pallet. The 2025 heat-treating guide gives Kiln-Direct’s 12 models 300 to 800 GMA pallets, Nyle 350 to 660 and SII 600 to 2,400. Fuel varies by maker: LP, natural gas, biomass, steam, hot water or electric. A kiln set up for natural gas will not run on biomass without work, so match the kiln to what you have.
Cycle time decides daily output: the same guide quotes heat-treating cycles from about 2 to 3 hours on some systems to 1 to 6 hours on others. Divide your working day by the cycle and multiply by the capacity for a rough count, and remember loading time.
Moving and recertifying
Plan the move with the agency in the loop. Some agencies will want to see the kiln running at the new site with probes in place before approving it. Allow for that time before you promise heat-treated pallets to a customer. The kilns themselves are on the kiln page, and exporting is covered on export pallet makers.
Running it after certification
Certification is not a one-time event. The agency audits the shop, the records of every charge are kept, and the HT mark on each pallet carries the shop’s registration number. The kiln’s probes need to stay calibrated, its recorder working, and the people loading it trained to place the probes in the thickest pieces. A used kiln with a reliable controller and good records is easier to keep certified than one where those were neglected.
Plan the loading too. A kiln holds a set number of pallets per charge, and how fast you can fill and empty it decides how many charges a day you get.
Who the agencies are
The American Lumber Standard Committee accredits the agencies, and the agencies certify the producers. Several agencies serve the pallet trade; the choice usually comes down to who has inspectors near you and who already knows your operation. If you already grade lumber or are enrolled for another program, start with that agency.
Budget for the time as well as the money. The agency’s first visit, any changes it asks for, and the test runs all come before you stamp the first pallet.
Probes, records and the stamp
Thermocouples go into the thickest pieces of the charge, the recorder logs every reading, and the operator keeps the printout or file with the charge number. Each HT stamp carries the country code, the producer’s registration number and HT. Inspectors compare stamps, charge logs and probe placement on audit visits. Lost logs mean lost certification, so back up digital records daily. Some shops hire certified heat-treating capacity from neighbours while their own kiln awaits approval. Calendar reminders help.
Sources for this guide
Ask about a kiln
Tell us the capacity in GMA pallets, the fuel you have and where it will stand. We will ask sellers about probes, records and how the kiln comes apart.
Heat-treat kiln