Used machines for pallet shops, by make and model.

Find me a machine
Menu
A gloved hand pushing a used pallet along the table of a bandsaw dismantler toward the blade

Bandsaw pallet dismantlers

A bandsaw pallet dismantler runs a long band blade flat across a steel table and cuts the nails between the deck boards and the stringers, so the boards come away whole. Makers rate them at roughly 400 to 1,000 pallets an 8-hour shift, depending on the model, the motor and whether one or two people feed it.

Bandsaw dismantlers: maker #model, blade, power and the makers’ own output claims
Maker and modelKindPowerSize and capacityMaker’s output claim
Industrial Resources Rapid Cut IIOne operator15 HP direct drive, 4,200 ft/min64 in table, 22 ft 10 in blade800 to 1,000 a shift[1]
Industrial Resources Wolverine IIOne worker; two-man option15 HP; single-phase option64 in table, 23 ft 9 in blade400 to 600 a shift[1]
PRS SpartanOne or two people10 HP direct drive, 2,200 SFPM21 ft 9 in blade[1]
PRS PROSAW 15, AT, AT-15One or two operators10 or 15 HP, belt driveFixed or powered table height[1]
Saw Service & Supply HawkTwo-man; one-man with flip bar off15 HP three-phase, 3,900 SFPM5/8 in steel deck60 to 90 an hour[1]
Smart Products one-operatorOne operator10 or 15 HP, 2,600 or 3,700 ft/min52 or 64 in base600 an 8-hour shift[1]
Smart Products portableTowable, normally 2-personGasoline, electric start52 or 64 in700 to 800 an 8-hour shift[1]
Universal Machinery Sales Mark IOne man; two-man setup10 HP single- or three-phase62 in table400 to 700 an 8-hour shift[1]
Universal Machinery Sales Run-A-GadeOne man; two-man option15 HPPneumatic blade tensioning[1]
Wood-Mizer PD200 Pallet HawgOne or two operators10 HP electric or 19 HP gas, 2,200 ft/min60, 72, 84 or 96 in tableabout 400 a shift[1]
Cam-Wood 1AM-010-2GGasoline13 HP engine60 x 48 in table, 251 x 1-1/4 in blade[2]

A dash means the maker’s page or the listing gave no figure for that column.

Output figures are the makers’ own claims as the source prints them, not our measurements.

  1. Pallet Enterprise dismantler guide, July 2025, read Nov 15, 2026
  2. Surplus Record, Pallet Nailers and Pallet Equipment, read Nov 15, 2026

Published asks

Bandsaw dismantlers: asking prices as listed
Maker and modelMachineYear and conditionListed fromAsk
Cam-Wood 1AM-010-2Bandsaw pallet dismantler, 10 HP2026, newCharlotte, NC, Surplus Record$8,925
Cam-Wood 1AM-010-2GGasoline bandsaw pallet dismantler, 13 HP, 60 x 48 in table, 251 in blade2026, newCharlotte, NC, Surplus Record$8,925

Asks, not sales: what each seller listed when we read the page on 15 Nov 2026. We are not the seller of these machines, and a listed machine may since have sold.

Blade speed, power and table width

Blade speed is quoted in SFPM, surface feet per minute. The guide’s machines run from 2,200 on the Pallet Hawg and the Spartan up to 4,200 on the Rapid Cut II. A faster blade cuts more pallets an hour; a slower one is usually the cheaper, lighter machine that a start-up shop can feed alone.

Power decides what a small shop can run. Most of these are 10 or 15 HP electric, and a 15 HP motor normally wants three-phase. If your building only has single-phase, the Wolverine II lists a single-phase option, the Mark I comes single- or three-phase, and the Pallet Hawg, the Cam-Wood 1AM-010-2G and Smart Products’ portable machine run on gasoline.

Table width sets the biggest pallet you can lay flat. The common widths are 52 to 64 inches; the Pallet Hawg goes to 96. If you take in oversize or skid pallets, say so in the request.

What to check before buying one used

Look at the blade guides first: worn guide bearings let the blade wander, and then it eats boards and blades. Spin the wheels by hand with the blade off and listen to the bearings. Run the table up and down; on the hydraulic and pneumatic lifts, look for leaks and slow travel.

Then the tensioner, the motor nameplate and the wiring. Ask what blade the seller runs and how many pallets it gets from one. Wood-Mizer says up to 1,500 pallets a blade on the PD200 and Smart Products says 1,200 to 1,500; the shop’s own number tells you how it has been run. The full list is in our dismantler checklist, and blades are on the blades page.

Installing one you bought

A bandsaw dismantler needs a level floor, room for pallets in and boards out on both sides, and somewhere for the stringers to go. Plan the board flow before the electrician comes: the trim saw usually sits right behind it. Ask the seller for spare blades and the blade-tension setting they ran, and check the wheel alignment once it is anchored.